The Champion Power Equipment 4200-PSI 15.1LPM Low Profile Petrol Pressure Washer provides cost-effective, "do-it-yourself" cleaning power. The combination of practical features with high-performance components results in better cleaning with less effort for all your outdoor projects.
This 4200-PSI pressure washer performs well under pressure no matter what the job. Whether your outdoor cleaning project involves your patio, deck, outdoor furniture, siding, fence, driveway, car, truck, boat, RV, farm equipment or something else, Champion’s low profile pressure washer has what it takes to tackle any job.
It’s important to choose the right nozzle for the job, since nozzle size affects water flow and pressure. The five quick-connect nozzles (0°, 15°, 25°,40°, soap) ensure maximum cleaning performance on any type of project.
Extend your reach with the included 15.2m high-pressure, quick-connect hose and use cleaning detergents hassle-free with the 1.2m detergent hose.
The Annovi Reverberi triplex pump is designed for high performance,high efficiency and long pump life and will ensure steady nozzle pressure for consistent cleaning performance.
Champion’s low profile design along with the 25.4cm solid tyres make this pressure washer easy to maneuver. The handy onboard storage for the high-pressure hose, trigger gun and spray wand ensure you’ll have what you need when you need it, plus you’ll be able to keep moving without having to stop and put things away.
The durable steel frame is built to last. Powered by a 389cc Champion single-cylinder OHV engine with a 6 litre fuel tank and designed with a low oil shut-off sensor, this unit has a 1.1 litre oil capacity (recommended 10W-30).
These pressure washers are mains feed only and require a minimum flow rate of 5ltr/min. They are not designed to be used with portable tanks or containers.
All newly manufactured products are EU Stage V Compliant.
Capacity | 289 Bar (4200 psi) |
---|---|
Engine | 389cc 12HP Champion OHV |
Fuel Capacity | 6.2 |
Oil Capacity | 1.1 |
Start Type | Recoil |
Low Oil Shutoff | Included |
Dimensions L*W*H (Fully Assembled) |
114 x 56.8 x 77.2cm (44.9 x 22.4 x 30.4 in) |
Nett Weight | 60.4 kg (132.2 lbs) |
Wheels | 25.4cm Solid |
Max Water Temp | 104°F (40°C) |
Chemical Injection | |
Min Flow Rate | 15.1 l/min |
Wand | Quick Connect |
Hose | 15.2m / 50ft |
Hose Storage | Built-in |
Warranty | 2 Years Limited |
Certification | EPA, CARB, CE, EU Stage V, E10 Petrol Compliant |
Most motor-driven products that you will connect to your generator need extra watts when they start, this is known as starting watts.
The Starting Watts listed on your generator is the wattage the generator can output for an average of 6 seconds (Inverter) or 10 minutes (Open Frame Type).
Once this period is over, and if the wattage has not reduced the Overload Protection will activate and the generator will trip using the following methods circuit breaker (frame type) and flashing overload light (Inverter), if this happens the power (wattage) needs to reduced or disconnected immediately and the generator needs to be reset by stopping the generator and turning everything to the ‘OFF’ position and leaving for minimum 2 minutes (Inverter Only).
The Maximum Watts listed on your generator is the MAX watts output the generator can run at – however it is not recommended to run your generator at the maximum watts for periods more than average 5 minutes (Inverter) and 60 minutes (Open Frame Type). Once this period is over, and if the wattage has not reduced the Overload Protection will activate and the generator will trip using the following methods circuit breaker (frame type) and flashing overload light (Inverter), if this happens the power (wattage) needs to reduced or disconnected immediately and the generator needs to be reset by stopping the generator and turning everything to the ‘OFF’ position and leaving for minimum 2 minutes. While working in the max zone on an Inverter you will have solid red overload light this is normal.